February 15th, 2010 by Robo

Fortunately, you don’t have to be an olympic swimmer to scuba dive, but you do have to be in good health. Before you begin your PADI course, you will have to have a medical examination. Your dive centre should be able to give you a list of doctors in your area who are qualified to do the scuba examination. Not all doctors will do these so don’t be surprised if your own doctor says that they can’t.

As long as you have a reasonable level of competency in the water i.e. you can swim 200 metres and float for 10 minutes, you should be OK. At the end of the day, you know how confident you are in the water. If you’re not very confident in the water, maybe consider some one on one lessons. Something to keep in mind – when you’re kitted up for scuba diving, you’ll be wearing a BCD (vest) that is fully inflatable and makes you totally buoyant. So another words, if you’re tired in the water, you’re BCD will make you float comfortably on the surface.
When you go to see the doctor for your dive medical, you will be asked lots of questions about your health history. Below is a list of possible health questions to consider.

Basic Dive Health Assessment

  • Could you be pregnant, or are you attempting to become pregnant?
  • Are you presently taking prescription medications? (with the exception of birth control or anti-malarial)
  • Are you over 45 years of age and can answer YES to one or more of the following?
  • Currently smoke a pipe, cigars or cigarettes
  • Have a high cholesterol level
  • Have a family history of heart attack or stroke
  • Are currently receiving medical care
  • High blood pressure
  • Diabetes mellitus, even if controlled by diet alone

Have you ever had or do you currently have…

  • Asthma, or wheezing with breathing, or wheezing with exercise?
  • Frequent or severe attacks of hayfever or allergy?
  • Frequent colds, sinusitis or bronchitis?
  • Any form of lung disease?
  • Pneumothorax (collapsed lung)?
  • Other chest disease or chest surgery?
  • Behavioural health, mental or psychological problems (Panic attack, fear of closed or open spaces)?
  • Epilepsy, seizures, convulsions or take medications to prevent them?
  • Recurring complicated migraine headaches or take medications to prevent them?
  • Blackouts or fainting (full/partial loss of consciousness)?
  • Frequent or severe suffering from motion sickness (seasick, carsick, etc.)?
  • Dysentery or dehydration requiring medical intervention?
  • Any dive accidents or decompression sickness?
  • Inability to perform moderate exercise (example: walk 1.6 km/one mile within 12 mins.)?
  • Head injury with loss of consciousness in the past five years?
  • Recurrent back problems?
  • Back or spinal surgery?
  • Diabetes?
  • Back, arm or leg problems following surgery, injury or fracture?
  • High blood pressure or take medicine to control blood pressure?
  • Heart disease?
  • Heart attack?
  • Angina, heart surgery or blood vessel surgery?
  • Sinus surgery?
  • Ear disease or surgery, hearing loss or problems with balance?
  • Recurrent ear problems?
  • Bleeding or other blood disorders?
  • Hernia?
  • Ulcers or ulcer surgery?
  • A colostomy or ileostomy?
  • Recreational drug use or treatment for, or alcoholism in the past five years?
February 14th, 2010 by Barry

IMPORTANT!!!! YOU MUST DO THIS BEFORE YOU USE YOUR SCUBA MASK FOR THE FIRST TIME!!!

Before you use your brand new scuba mask for the first time, you MUST remove the invisible oily residue or liquid silicone that may still be on your mask!! It may be left over from manufacture or may have been applied to protect your mask during shipping. If you don’t remove all of this, your mask is likely to fog up underwater and you will have extreme difficulty in clearing it. This is obviously something that you do not want and it will ruin your dive if you have to stop every 30 seconds to try to defog your mask. It may also stop your mask from adhering to your face properly and it may slip off..

There are a few different ways of cleaning your mask for the first time:

You can purchase a mask cleaning solution from a dive shop. Just make sure you read the instructions carefully as some of these can be harmful to plastics.

You can use toothpaste (not gel). Squeeze out about a 5 cent piece size amount of toothpaste onto the INSIDE of the dive mask. Rub it around with your finger in small circular motions. Make sure you go right into the edges. You will need to do this for about 15 minutes. Rinse out with fresh water VERY WELL to avoid toothpaste burning your eyes when you dive.

Some say you can use a non-abrasive dish-washing liquid but I’ve never found this effective as you have to use something slightly abrasive to remove the film.

February 13th, 2010 by Taryna

If the thought of immersing yourself in incredible underwater sceneries and witnessing amazing underwater creatures gives you tingles, then reef diving is for you!

The Great Barrier Reef, located in the Coral Sea off the coast of Queensland, is one of the most popular reef diving destinations in the world. One of the 7 natural Wonders of the World, it stretches over 2,600 km’s along Australia’s East Coast and is composed of over 2,900 individual reefs and 900 islands! Beginners and experts alike are always amazed by what they see in this underwater paradise!

The calm waters around the reef make it possibly the best location for scuba diving in the world! The water can be quite deep in certain places, but is generally OK for amateurs to dive in. For beginners, diving should always be in shallow waters of no more than 18 metres in depth. There are however reefs around the Coral Sea where the depth is about 91 metres which is awesome for expert divers!

You can spend weeks exploring the reef, so if time is no issue, you could consider jumping on one of the popular live-a-board boats. These specialized boats take visitors right to where the action is. Many such boats have convenient luxury amenities and can organize boats to take divers right to the centre of the reef. There are day boats available for day-time scuba diving. These day boats take visitors for 4 to 5 hour trips into the reef. Even local resorts organize these day boats for their guests.

Whilst enjoying The Great Barrier Reef, it is important to recognise that as the world’s biggest single structure made by living organisms (which can even be seen from outer space!!), we need to protect the reef for future generations. A large part of the reef is protected by the Great Barrier Reef Marine Park. This helps to limit the impact of human use, such as over fishing and tourism. So make sure the only thing you fire is your flash and the only thing you shoot with is your camera!

As scuba diving increases in popularity, more and more diving packages are available. Many resorts offer scuba packages and I know we are keen to start organising our own scuba trip packages, both within Australia and overseas, including flights, accommodation and of course SCUBA DIVING!!

February 13th, 2010 by Robo

When you start to look at getting your scuba diving gear, you’ll be amazed at the large amount of choices you have. There are a lot of different fins available. Flexible fins may be comfortable to use where there is little or no current, however in strong current they aren’t going to do you much good! You need fins that can move a lot of water without bending, split fins like the “Talaria” delivers more forward-going thrust than a conventional fin and are great for moving water fast.Diver in swell

Technique – when the current reduces slightly, take advantage of it and use it to relax your leg muscles a little but still try to cover some ground the best technique for this is the flutter kick, pace yourself so that you can maintain the speed, and take advantage of the changes in current . When you use a steady powerful kick, make sure you don’t open your legs too wide, as doing this will cause drag and reduce the effectiveness!

Ground Cover – Use the landscape to shelter from the current this can allow you to rest for a few moments.

Your hands – This obviously isn’t the most ideal situation, but if you really have to!  you can use your hands to pull yourself along or at least hold on for a few seconds.

Depth to swim at – Stay as close to the bottom as possible without damaging the reef, the current will always be less.

Dive Plan – Make sure you plan your dive! head into the current for the first part of your dive, if you don’t like strong current, don’t dive! You could also plan a drift dive, so the boat will pick you up when you surface.

Head up – Lastly were posible keep your head up looking in front rarther then face down, this will stop you feeling sea sick!!

February 12th, 2010 by Robo

So you’ve spent weeks or maybe even months researching what scuba gear to buy, you’ve spent your hard earned cash and you are now the proud owner of your very own scuba gear. You want to keep it in the best condition possible so washing your gear is critical. This will also ensure that your gear performs as it is supposed to and is safe.

Setup
The most common way to wash gear is to use a large tub filled with water. (Large black tubs are usually available from Bunning’s). You can also use a hose or sink instead. Many dive shops use two separate tubs, one containing water and detergent for washing wetsuits and booties, and one filled with fresh water for all other gear. If you’ve been shore diving, you may have sand or dirt on some of your equipment so it’s a good idea to rinse this off before washing the gear in the tub.

Regulator
The number one rule when washing your regulator is ensuring that your dust cap is securely in place. This ensures that no water enters the first stage regulator which has internal components that are sensitive to moisture. Before attaching the dust cap, it is best to dry the inside of it and of the opening in the first stage regulator. The most common method is to blow it out with air from the dive tank (this can be loud though). Another method is to use a dry cloth. Once the dust cap is securely in place you should completely submerge your regulator in fresh water and allow it to soak for at least 5 minutes. Avoid depressing the purge buttons on either second stage regulator while they’re in the water as this will allow water to flow into the first stage regulator. Once the regulator has soaked for a while you can hang it up to dry.Scuba Gear

BCD
Washing your BCD is done in two steps:
The first step in washing your BCD is to completely submerge it in fresh water and dunk it up and down several times until all salt water and dry salt crystals have been washed away.

The second step is to wash the inside of the BCD. When you’re underwater small amounts of salt water can enter the inside of your BCD through the exhaust valves and low pressure inflator. It is necessary to wash all of this water out as salt water eventually dries inside leaving behind salt crystals which can build up over time and cause exhaust valves to malfunction and the internal bladder to tear. Begin by pushing down on the deflate button of the low pressure inflator while using a hose to pour fresh water into the exhaust valve. Once the bladder is one quarter filled, thoroughly shake the BCD around to allow the water to move all around the inside. Once you’ve completely rinsed the inside it’s time to empty the bladder. The best method is to empty the water through each of the exhaust valves which allows them to be rinsed as well. Now you have a clean and rinsed BCD, partially inflate the BCD by blowing into the low pressure inflator and hang it up to dry.

Dive Computer and Camera
Follow the manufacturer’s recommendations when caring for these. It is generally recommended to thoroughly rinse dive computers and cameras in fresh water. You may also like to allow them to soak for an extended period. Remember to thoroughly dry your camera before you open its housing.

Wetsuit, Booties, and Gloves
Your wetsuit, booties, and gloves should always be washed in fresh water. You may also like to use some wetsuit wash, a disinfectant detergent available at most dive supply stores. Wash the suit, booties, and gloves by submerging them in water and dunking them up and down and turning them inside out as well to ensure that both inside and outside are completely clean. Afterwards you can hang the wetsuit on a strong coat hanger to dry. The booties and gloves should also be hung up to dry.

Fins, Mask, Snorkel, and Other Equipment
All of your other equipment should also be submerged in fresh water, dunked up and down until clean and hung up to dry.

January 16th, 2010 by admin

The ability to bring more of California’s coastline to life with the creation of artificial reefs passed a critical hurdle Tuesday when the State Assembly Committee on Judiciary unanimously approved AB 634.  The bill will now be sent to the Assembly floor, where it could be voted on as early as January 18, 2010.

One major block to artificial reef projects has been the fear of liability if accidents occur while people are SCUBA diving at these sites.  AB 634 protects state and local agencies from legal liability, making it possible for these agencies to support bringing these projects to their harbors.

This bill was sponsored by California Ships to Reefs, a nonprofit organization that has worked tirelessly with state governmental agencies to lay the groundwork for artificial reef projects on the state’s coast.  The reefs are created by sinking decommissioned military or retired commercial vessels in appropriate locations after they have been stripped and cleaned.  New habitats for ocean creatures quickly create new SCUBA diving and fishing sites.  Recreational opportunities bring needed revenue to local businesses.

The bill, authored by Diane Harkey (R-Dana Point), enjoyed support from all seven Judiciary Committee members present and even had a delegation of supporters sent by Orange County’s supervisors speaking in its favor.

“This is a pivotal time,” said Joel Geldin, California Ships to Reefs Chairman and CEO.  “To get this bill through the Legislature and on the governor’s desk, we need supporters to tell their representatives how important AB 634 is.  We recommend people call, fax and email their representatives, since this vote is only a few days away.

“Artificial reefing is a proven success in other states, such as Florida, and internationally, as in British Columbia,” Geldin noted.   California can enjoy these benefits too, giving the diving and fishing industries the boost they need, while bringing millions of dollars into many parts of the state’s economy.”

Geldin urges supporters to contact their representative immediately.  You may find out who your Assembly representative is at http://www.assembly.ca.gov/defaulttext.asp

California Ships to Reefs is a 501(c)(3) Non-Profit Public Benefit Corporation seeking to reef surplus ships as artificial reefs, bringing diving and fishing tourism to local ports in California and enhancing the Ocean Environment.

For further information, please visit the organization’s website at http://californiashipstoreefs.org, or contact state Governmental Relations Committee Chairman Dean Rewerts at (530) 906-6465.

January 16th, 2010 by admin

The Great Barrier, Reef is a distinct feature of the East Australian Cordillera division. It includes the smaller Murray Islands.[11] It reaches from Torres Strait (between Bramble Cay, its northernmost island, and the south coast of Papua New Guinea) in the north to the unnamed passage between Lady Elliot Island (its southernmost island) and Fraser Island in the south. Lady Elliot Island is located 1,915 km (1,190 mi) southeast of Bramble Cay as the crow flies.[12]

Australia has moved northwards at a rate of 7 cm (2.8 in) per year, starting during the Cainozoic.[13] Eastern Australia experienced a period of tectonic uplift, leading to the drainage divide in Queensland moving 400 km (250 mi) inland. Also during this time, Queensland experienced volcanic eruptions leading to central and shield volcanoes and basalt flows.[14] Some of these granitic outcrops have become high islands.[15] After the Coral Sea Basin was formed, coral reefs began to grow in the Basin, but until about 25 million years ago, northern Queensland was still in temperate waters south of the tropics – too cool to support coral growth.[16] The history of the development of the Great Barrier Reef is complex; after Queensland drifted into tropical waters, the history is largely influenced by how reefs fluctuate (grow and recede) as the sea level changes.[17] They can increase in diameter from 1 to 3 centimetres (0.39 to 1.2 in) per year, and grow vertically anywhere from 1 to 25 centimetres (0.4–12 in) per year; however, they are limited to growing above a depth of 150 metres (490 ft) due to their need for sunlight, and cannot grow above sea level.[18] When Queensland moved into tropical waters 24 million years ago, some coral grew,[19] but a sedimentation regime quickly developed with erosion of the Great Dividing Range; creating river deltas, oozes and turbidites, which would have been unsuitable conditions for coral growth. 10 million years ago, the sea level significantly lowered, which further enabled the sedimentation. The substrate of the GBR may have needed to build up from the sediment until the edge of the substrate was too far away for suspended sediments to have an inhibiting effect on coral growth. In addition, approximately 400,000 years ago there was a particularly warm interglacial period with higher sea levels and a 4 degree Celsius (7.2 degree Fahrenheit) change in water temperature.[20]

The Great Barrier Reef is clearly visible from jet planes flying over it

Heron Island, a coral cay in the southern Great Barrier Reef

The land that formed the substrate of the current Great Barrier Reef was a coastal plain formed from the eroded sediments of the Great Dividing Range with some larger hills (some of which were themselves remnants of older reefs[21] or volcanoes[15]).[13] The Reef Research Centre, a Cooperative Research Centre, has found coral ’skeleton’ deposits that date back half a million years.[22] The Great Barrier Reef Marine Park Authority (GBRMPA) considers the earliest evidence to suggest complete reef structures to have been 600,000 years ago.[23]According to the GBRMPA, the current, living reef structure is believed to have begun growing on the older platform about 20,000 years ago.[23] The Australian Institute of Marine Science agrees, which places the beginning of the growth of the current reef at the time of the Last Glacial Maximum. At around that time, the sea level was 120 metres (390 ft) lower than it is today.[21]

From 20,000 years ago until 6,000 years ago, the sea level rose steadily. As it rose, the corals could then grow higher on the hills of the coastal plain. By around 13,000 years ago the sea level was 60 metres (200 ft) lower than the present day, and corals began to grow around the hills of the coastal plain, which were, by then, continental islands. As the sea level rose further still, most of the continental islands were submerged. The corals could then overgrow the hills, to form the present cays and reefs. Sea level on the Great Barrier Reef has not risen significantly in the last 6,000 years.[21] The CRC Reef Research Centre estimates the age of the present, living reef structure at 6,000 to 8,000 years old.[22]

The remains of an ancient barrier reef similar to the Great Barrier Reef can be found in The Kimberley, a northern region of Western Australia.[24]

The Great Barrier Reef World Heritage Area has been divided into 70 bioregions,[25] of which 30 are reef bioregions,[26] and 40 are non-reef bioregions.[27] In the northern part of the Great Barrier Reef, ribbon reefs and deltaic reefs have formed; these structures are not found in the rest of the Great Barrier Reef system.[22] There are no atolls in the system,[28] and reefs attached to the mainland are rare.[13]

Fringing reefs are distributed widely, but are most common towards the southern part of the Great Barrier Reef, attached to high islands, for example, the Whitsunday Islands. Lagoonal reefs are also found in the southern Great Barrier Reef, but there are some of these found further north, off the coast of Princess Charlotte Bay. Cresentic reefs are the most common shape of reef in the middle of the Great Barrier Reef system, for example the reefs surrounding Lizard Island. Cresentic reefs are also found in the far north of the Great Barrier Reef Marine Park, and in the Swain Reefs (20-22 degrees south). Planar reefs are found in the northern and southern parts of the Great Barrier Reef, near Cape York, Princess Charlotte Bay, and Cairns. Most of the islands on the reef are found on planar reefs.[29]